auto scanner tool - Professional Auto Diagnostic Tools Supplier.
autoscannertool by autoscannertool @
Daily car maintenance is very important. A slight effect on daily maintenance will not only cause unnecessary damage to the vehicle, but also endanger the safety of traffic. On the contrary, if the daily work done carefully, not only can make the vehicle to maintain a regular new, but also to avoid traffic accidents. In fact, the daily maintenance work is very simple, simple is: clean, tighten, check, supplement.
One, clean
The air contains a lot of dust, sediment and acidic substances, not only easy to leak oil adhesion, easy to form the high temperature baking insulating layer hard, the heat dissipation performance of parts of the variation, and it is prone to electrostatic adsorption and the erosion of the body paint, paint and oxide.
We should not only pay attention to the general clean car paint clean, also want to pay attention to the car interior, car engine, car air conditioning and cleaning wheel etc..
Two, fastening the vehicle after cleaning, it is to be on the connection of the fastening. Due to vibration, bumps and swing of the dry line, the connection piece is bound to be loose and wear. Therefore, in the daily maintenance should be timely tightening. The connecting piece fastening daily work is directly related to traffic safety, especially the important parts of steering, braking, transmission, must not be let down. If the engine around the joint of the hose to tighten, anti oil leakage. Secondly, fasten all the lines and connectors for electric equipment, electric equipment to work normally prevent open circuit and short circuit and ground effect etc.. Again, the main connection parts for inspection and fastening, such as the generator drive belt, steering linkage brake device connection point, the transmission system and tires, etc..
Three, check the connection parts, should check the oil liquid height and quality, because the liquid at high temperature will gradually loss and oxidation and lead to lower level of the liquid and performance change. 1, check the battery level.
With a diameter of 5 N 6mm tubes from the liquid inlet and the vertical force to screen after contact is closed with the thumb of the lift tube tube, measuring the height of liquid column is the battery level, standards should be 10 N 15mm. 2, check the oil level height of the car cold dipstick out, wipe, into oil pan bottom, after observing the height between the upper and lower line. The car should be stalled, the oil into the oil pan after measurement. 3, check the coolant level the height of the car cold cooling liquid in the tank is full, the expansion tank level should be in line. The hot liquid height should be slightly higher than. 4, check the brake fluid, liquid level to unscrew the bolts, direct observation of liquid level in the specified range of markings. 5, check the quality of oil, whether it is the oil, can use the following methods to check.
(1) the appearance of law: check oil samples taken, if more transparent, not that serious pollution; if a fog, while oil seeps in the water; if a grey, may be lead or other abrasive contamination; if is black, it is polluted by high temperature exhaust gas. (2) diffusion method: a drop of oil samples will be taken on the filter paper, if the diffusion is very wide and there is no obvious difference between the oil droplets and the diffusion zone, it shows that the oil is clean and good.
Mercedes Benz MB Star C3 Diagnosis With Latest Software
1.This is the Mercedes MB STAR C3 Diagnose Tool works on Car 12V and Heavy Duty 24V.
2. It has real PCB in RS232-485 cable.
3. The price is with 120GB hard drive which include Xentry,DAS,WIS,EPC,SDMedia,StarFinder ect.
4.High Quality Compact 3 Star Diagnosis Tool with 2 years warranty.
You can go to GO2OBD.NET buy MB Star C3.
autoscannertool by autoscannertool @
For a particular brand of car, due to the use of zero with the same quality control, according to a unified standard, and on the same production line assembly in accordance with the strict process, so the performance index of each engine, there is no significant difference. However, in actual use, the service life of each engine is not the same, some use 500 thousand km without overhaul, and some are less than 100 thousand km, the engine will appear, burning oil, etc.. The same production line produced products, why there will be such a big difference?
The key lies in the proper use and maintenance of the car.
So in the daily use of the car, how to do to do the correct operation and maintenance of it?
1 pay attention to the new car of the close period
Go together in the new period, the engine parts cooperate with each other to rough surface will be removed, gradually formed a relatively smooth surface, improves the surface quality of the parts and the fitting accuracy, to work under normal load. So the working condition of the engine is directly related to the service life of the engine. Vehicle must pay attention to during the period of.
The high speed is prohibited. The car at the speed of the vehicle shall not exceed 70% of the maximum speed of the engine. Long time high speed is not allowed.
The non overload operation, not allowed to overload. As soon as the engine works, it is changed into low gear.
The engine started, not allowed to slam on the accelerator pedal, until the water temperature reaches the normal humidity, then a smooth start. Straight from a block must be used.
I don't drive in a bad way, reduce vibration and shock. In driving should reduce the sudden acceleration caused by overload phenomenon, such as emergency brake, long time brake or use the engine brake, etc.. As far as possible to choose a good road speed, the best results.
Note that the engine coolant temperature, oil level, found that failure to promptly eliminate.
Go right after the end of a car go maintenance.
2 adhere to the first warm car, after the start
Some drivers in the start of the car, often by a few feet close to the accelerator, so that the engine running. As everyone knows, this will cause great damage to the engine parts. Because the engine starting (especially cold start), the engine working humidity is low, the internal parts surface does not achieve sufficient lubrication, if the engine high work load, make the internal parts wear increase, change with the normal clearance.
Good driving habits should be after the engine start, the first pre heating, so that the engine coolant to reach the normal operating temperature (at least to reach more than 50 degrees Celsius), and then to improve.
BMW ICOM A2+B+C ISID Diagnostic Tool With Newest Native ISTAD/P Software
This BMW ICOM A2+B+C Diagnostic Tool with latest 12.2015 Rheingold ISID ISIS software + bmw engineer tool( includs E-sys, Inpa, Ediabas, NCS and so on) in 500GB hard disk used on win7 32bit system.
Highlights of BMW ICOM A2+B+C With Newest BMW ISTA Diagnose Software:
1. High quality BMW ICOM A2 diagnostic tool with heat sink and brand new cpu processor.
2. Latest V12.2015 BMW ISTA Rheingold and Engineer Tool in 500GB HDD.
3. All softwares pre-installed without dongle, only need to insert it into laptop.
BMW ICOM A2+B+C is a professional diagnostic & program tool for BMW group vehicles include Mini,Rolls-Royals. It is second generation BMW ICOM with robust construction, faster processor,bigger storage than its previous version.
You can go to GO2OBD.NET buy bmw icom.
autoscannertool by autoscannertool @
Car maintenance and repair are closely related. Repair, maintenance, repair, repair. In the vehicle maintenance process may be found precursor or in one part of the works will malfunction or damage, thus can be used to repair maintenance time. In the repair process, maintenance of some damaged parts should be, this is a very natural thing. So how do we take care of our cars in our daily lives, let's look at the information below.
Four, cooling system cleaning and maintenance
1. In general, the car in the summer and winter season should be cleaning and maintenance time, normal driving every 6 to 8 months cleaning and maintenance time, or when the water temperature is too high, Water Leakage, boil when cleaning and maintenance time. Remove the engine tends to overheat and traces of the scale, to prevent the occurrence of harmful corrosion, avoid and prevent leakage and seal the coolant tank, completely replaced the old.
2, power steering system cleaning and maintenance
Car every driving 40000km-45000km cleaning to be maintained once, or in case of a steering difficult system leakage, replacement power steering machine parts, it is also required to clean and maintain a. Scavenging system of harmful sludge, varnish, clear turn difficult at low temperatures, to stop and prevent the leakage of hydraulic power steering, steering clear noise, completely replaced the old brake steering fluid.
3, fuel system cleaning and maintenance (that is, cleaning nozzle, valve carbon)
Under normal circumstances, the car should be cleaned and maintained 1 times per driving 10000km-15000km, or when you find that the engine is panting, sluggish and accelerate poor, take black smoke, weakness, cleaning and maintenance of oil when the 1 times. The removal of the system inside the resin and carbon, prevent harmful corrosion, avoid and stop the seal and water tank leakage, completely replace the old coolant.
As long as we usually pay attention to the car's maintenance, attention to detail, our car will be able to better maintain the new appearance.
LAUNCH X431 Diagun III 3 Scanner Original
LAUNCH X431 Diagun III 3 Scanner Original is LAUNCH's newly develpped Universal Scanner which is based on its previous version X431 Diagun. It covers more vehicles than the old X431 Diagun and has some progress to let this machine to be more friendly.
LAUNCH X431 Diagun III 3 features and progress as below:
1.X431 Diagun III connects cars through DBScar adaptor by Bluetooth.
2.Powerful diagnostic function let Diagun III 3 works on most of Asia,US and Europe vehicles.
3.More friendly Interface let You now can go into diagnostic system directly after starting machine.
4.Compact design to make it slim on your hands!
5.Compact design makes DBScar connector avoide of dust & oil by window.
6.Diagun III 3 support standard USB printer.You can print diagnostic result.
7.Continually update makes you works on more and more cars.
8.Better battery system makes Diagun III 3 non-stop working for 10 hours!
You can go to GO2OBD.NET buy LAUNCH X431.
autoscannertool by autoscannertool @
A car is convenient for people's life, but also so many do not understand the car owners think car beauty and maintenance is very troublesome, in fact, car beauty and maintenance although time spent, if the owners find the right method for the project can also be a lazy car, also can let the car stay beautiful and good performance.
1 reasonable purchase of insurance
Many owners in the purchase of auto insurance, often buy "excess insurance (Fang Xinbao)" and "inadequate insurance". Excess insurance, the insurance limit is higher than the actual value of the insurance subject, such as the purchase of a $120 thousand car, the insured amount of 300 thousand yuan stolen, if the total loss, the compensation is only 120 thousand yuan. The "insurance law" thirty-ninth paragraph second: the insurance amount shall not exceed the insured value, exceed insurance value, excess is invalid, i.e. the insured can get appropriate compensation for the loss of the subject-matter insured, but not because of the purchase of insurance to get beyond the subject-matter of the insurance value of income from. In addition, the full amount of insurance, the insured amount is less than the actual value of the insured value, this situation will be paid in proportion".
2 imports of tires is not necessarily the best choice
Car in the driving, in fact, to the four tires. However, in the purchase of various brands of imported tires, some people will inevitably enter the purchase of the erroneous zone. Many consumers out of psychological factors, more willing to choose the original imports of tires. In fact, the introduction of new tires abroad for domestic users, the price is too high, and it does not necessarily apply.
3 adequate for tire inflation
Correcting the tire pressure is the most important part of the safety inspection. Low tire pressure will result in abnormal wear or damage the tire tire pressure is too high, will make the tires and wheels are more susceptible to the impact of the uneven pavement deformation, or even cause a puncture. Tire pressure must be checked regularly, in addition to the spare tire, the other at least two weeks to check again, and tire pressure check must be conducted in the tire cooling conditions, otherwise the high temperature will make the tire pressure increased, the amount of up to. Also don't forget to regularly check the spare tire pressure is normal.
Master these you can easily keep your car in good condition.
VAS 5054A VW AUDI SKODA SEAT Diagnostic Tool Good Quality
This is VAS 5054A used for VW group cars include VW,AUDI,SKODA,SEAT,Bentley and Lamborghini. The latest software is ODIS 2.2.4, with bluetooth function and full chip OKI.
The VAS 5054A is used for VW group cars include VW,AUDI,SKODA,SEAT,Bentley and Lamborghini.Now our VAS 5054A Diagnostic Tool is with ODIS software. It is with bluetooth function and its software is in multi languages( please tell me what language of software you need when you buy it).
The latest version of ODIS software is 2.2.6
Highlights of this VAS 5054A VAG Diagnostic with ODIS Software:
1. Good quality VAS 5054A Diagnostic tool with bluetooth function.
2. ODIS 2.2.4 support multi languages.
3. Full chip with OKI chip (for UDS protocol)..
4. Recognize ignition without any problem.
You can go to GO2OBD.NET buy VAS 5054A.
autoscannertool by autoscannertool @
A car is convenient for people's life, but also so many do not understand the car owners think car beauty and maintenance is very troublesome, in fact, car beauty and maintenance although time spent, if the owners find the right method for the project can also be a lazy car, also can let the car stay beautiful and good performance.
The following is the China second-hand car owners to edit share 8 car beauty and maintenance skills, to help owners to easily keep the car.
1 protection car paint with automotive coating replacement
Waxing and glazing paint protection is in the high-end car owners pay more attention to the automobile cosmetology project, it is a waste of time often go to waxing and glazing, automobile coating is a gradual replacement of wax sealing glair automotive beauty items, coating paint can be completely sealed, form a layer of film layer more than 3-8 times the hardness of paint on the body the paint is not guaranteed, oxidation, corrosion, avoid minor scratches etc.. The automobile coating warranty time can reach 2-5 years, as long as the owner of the car center can protect the car paint. In addition, the interior cleaning and disinfection for 3 months to do it once, to the professional car beauty shop for interior cleaning, and coated with a layer of protective glazing agent can make the car to keep the car feeling.
2 simple parts themselves can be replaced
Wiper and so on, these two replacement and inspection are relatively simple, to buy their own online brand, and then carry out a simple inspection and installation on it.
3 proper maintenance is scientific
Car maintenance cycle refers to the distance between car maintenance mileage or time. There should be periodic maintenance, don't like spoiled children as spoil your car, although frequent maintenance is not a bad thing, but there must be periodic, avoid excessive maintenance caused by internal discomfort. In the early stage of the car is mainly normal maintenance, the cost is relatively low; when the vehicle is used for certain length of time or after a certain mileage will enter the maintenance period, the cost is relatively high. General car condition good new car, can be appropriate to extend the maintenance cycle; while the car is in poor condition or the use of poor conditions, it should be appropriate to shorten the maintenance cycle.
Mercedes Benz MB Star Diagnose C4 ( SD Connect ) With Latest Xentry
Mercedes Benz MB Star Diagnose C4 (SD Connect) With 9.2015 latest xentry,das, EPC,WIS software for Mercedes group 12V cars & 24V heavy duty after 2000 which also support UDS vehicles. Support wireless and lan cable connection, K line,CAN BUS and UDS protocol.
The new generation for Mercedes Benz SD connect c4 is the latest one on market for all current and new coming MB vehicles. SD Connect Compact 4 is a latest Benz wireless multiplexer. It will connect to the PC by wireless connection.
Highlights of Mercedes Benz MB Star Diagnose C4 (SD Connect):
1. Newest Update software 2015.09 xentry, das, EPC, WIS and so on.
2. Firmware (Bootlmage and CSD) can be updated for newer version.
3. Brand new relays and TDK 701 Filter for stable connection with 2 years warranty.
4. With good Wlan card build in card slot and FREE GIFT Intel Wireless Card!
5. Support both WiFi AND Lan cable connection. more easy to use!No need COM port computer.
You can go to GO2OBD.NET buy mb star c4.
autoscannertool by autoscannertool @
The new owner of the best he has a record of the new owner of the car himself is best to have a detailed record. For example, when traveling to 5000 km, what to do in the maintenance, up to 40 thousand kilometers, whether the change of brake and so on, must be aware of. For each car maintenance, replacement of parts, are recorded in detail, like the "record card", be well aware of the car. The author also reminded the new owner, must spend some time to see the car's manual, a detailed understanding of the use and maintenance instructions about the car, and to read it as much as possible, in addition also should see more models of the forum, many of the old owners will be a lot of new car owners do not know the practical function the rich network of resources are of great help for better driving, car. Glass quickly remove fog inside the cold weather, sitting in the car too much, the temperature inside the car, the car is easy to produce gas, the glass is easy from the mist, blocking the driver's line of sight, the hidden potential danger. To solve this problem, then, put the switch to wind blowing the front windshield, with hot air, usually to open a file you can; if there is fog on the train, the first open air conditioning, fog soon dissipated, and then open hot air. The tips for autumn and winter travel is also very practical. Often check the oil and water to suggest that the new car should be mainly formed every week to check a good habit of oil and water, to see if they are not enough, the leakage does not leak. If it's not enough, make sure why. Car maintenance knowledge in general, if the decline is not large, basically belong to the normal loss. The oil circuit includes brake oil, gear box oil, engine oil, etc.. Some cars, the gearbox oil can not see, the owner can see where there is no parking leaking. Each run long distance, but also should be fully detected in the car's water, cooling liquid, etc., if the sun, but also check the rain enough to scrape the water.
FGTECH Galletto 2 Master Tunning Tool Plus BDM Adaptors
FGTech Galletto 2 Master BDM-TriCore-OBD Plus BDM adaptors is a famous chip tuning tool for all cars, trucks, motorcycles, Marine, BDM MPCxx, BDM Boot Mode Tricore, checksum. This item cannot only work as FGTech Galletto 2 Master, but can also work for BDM-TriCore-OBD. This FGTECH Galletto 2 is with BDM adaptors make job so easy.
FGTECH GALLETTO 2 MASTER ( BDM-TriCore-OBD ) V11.9. Software version is V52.
(MPC5xx - EDC17 - Infineon TriCore - ST10Fxx - OBD2 (K-CAN)
FGTech Galletto 2 Master this new system developed with high-speed USB technology is the fastest and most secure product on the market, it is easy to install and use by anyone. Our system comes furnished complete with all Car, Truck, Motorbyke, Marine, BDM MPCxx , BDM Boot Mode Tricore, checksum.
If you want to buy fgtech, you can go to GO2OBD.NET.
autoscannertool by autoscannertool @
First, we must learn to drive car to learn to find their own fault ""
Car in the use of the process, it is inevitable failure. For experienced drivers, usually can be "one step" to find the problem. And most people are helpless in the face of failure. Now learn to look for trouble.
Vehicle failure can be roughly divided into three parts:
One circuit fault; two is the oil circuit fault; three is the driving system failure, such as steering, braking, transmission parts, etc..
Among them, the circuit fault is divided into high voltage circuit and low-voltage circuit fault. In practical use, the fault of the vehicle is about 60% circuit failure, 30% in the oil circuit, most of these failures can be ruled out of their own. Only about 10% is the driving system failure, which is a mechanical failure, most of the time when the vehicle can travel, should go to the nearest special maintenance station repair.
When you are driving in the failure, one should not worry, two is not busy hands, first look at the relevant fault indicator to reflect the situation. Quiet down to the heart, analysis of the phenomenon of failure, ask a few why? Method of judgment and identification of oil circuit fault has two: one is driving on the way is stalled suddenly or slowly flameout, suddenly turn off mostly circuit fault; slowly flameout, or the vehicle continuously "jump" phenomenon, mostly circuit fault. Two is the "test fire", if there is no central high pressure fire, sub cylinder fire, it is a circuit failure, such as high pressure fire, the problem is in the oil circuit. And mechanical failure is mostly accompanied by abnormal sound, sound with the speed of the speed and change, stop the sound disappeared, and the oil circuit is not directly related to the fault.
With "by paragraph of the negative law", "focus" locked in a specific place, first figure out what kind of fault is the first to see whether the external anomaly. If the wire is not open, short circuit, there is no loose connection parts; engine, there is no wire burning smell, oil pipeline has no oil leakage, etc..
It is worth mentioning that the car now mostly EFI car, electronic control of combustion, less failure, contrary to the old carburetor car fault probability. Remember, the EFI cars such as circuit failure, often requires a dedicated computer tester, the driver should not do it yourself, so as not to damage the circuit program.
LAUNCH X431 Creader VII+ Code Scanner Global Version (Instead of CRP123)
LAUNCH X431 Creader VII+ Code Scanner Global Version is developped for insteading of LAUNCH Creader CRP123.It is compatiable for vehicles from 1996 to now via OBD.LAUNCH Creader VII+ has functions of read/clear codes,data stream graphic,store and playback of dynamic data stream.
LAUNCH X431 Creader VII+ Code Scanner Global Version also have below highlights:
1.Internet update to cover newest models.
2.Multi language supported: English,French,Spanish ( will be more languages in future)
Functions details of LAUNCH X431 Creader VII+ Code Scanner Global Version:
Applicable for all vehicles which match OBDII standard after 1996II
Supports all 10 test modes of the OBD
Display DTC help information and service information
Oxygen sensor test, carbon canister test
OBDII Data Stream Graphic Display
Cover more than 20 main car models in America, Europe and Asia Pacific regions
Can test Engine, Transmission, ABS and Airbag systems
Read DTC
Clear DTC
Read Dynamic Data Stream
Support Online Upgrade
You can go to GO2OBD.NET buy LAUNCH X431 Creader VII+ Code Scanner Global .
autoscannertool by autoscannertool @
1 let the engine idling a few seconds to moderate.
In the cold weather before driving engine idling a few seconds, to ensure proper flow and engine oil lubrication. Why hot? Because the parked car after a long time, engine oil back into the oil pan, the engine when the upper part of the lack of lubrication oil in the car after a while, the oil pump operation, then the oil transported to the need to lubricate the piston and connecting rod etc..
2 check the tire surface, with tire don't use.
If the tire wear is severe or irregular wear, it may indicate that the wheel alignment problem or the front part has been worn. Don't tire with the so-called "injured" tire is generally refers to the tire on the side wall of the leak, the owners in the daily driving path is more complex, so a puncture phenomenon can hardly be avoided. The tire is generally positive prick leak can be repaired, can also fill after normal use, but if the tire side wall or side wall of the tire and tire surface angle of the leak cannot be repaired, even fix it don't use. Daily traffic should frequently check whether the tire damage, such as: the surface of tire is pinned, cut phenomenon, once the damage was found to timely repair or replacement. If you find that there are a number of tire tread groove, etc., but also to remove in time to avoid the deformation of the tire crown. In addition, do not let the tire contact with oil and chemicals.
Renault CAN Clip Diagnostic Tool Plus Newest Software
This is Probe Renault CAN Clip diagnosing & programming tool for Renault cars from 1998-2015, the newest software is V151 provide multiple languages, support ISO and CAN, with full chip PCB always stable quality.
Highlights of Porbe Renault CAN Clip Diagnostic Tool Plus Newest Software
1. Software version: V151
2. Best Can Clip with full chip PCB support ISO and CAN
3. Diagnose Renault cars (1998-2015) including automatically test all Renault models' computers, reporgramming, airbag test and other functions
4. The firmware can be updated in future by newer software, NO 20% block problem
Renault can Clip Diagnostic Tool Installing Steps:
1. Please make sure your laptop is WINXP or WIN7 32 Bit system because Probe Renault CAN Clip does not run 64 bit system. We recommend WIN7 32 Bit system because it is more easy to install drivers.
2. Please install Crack BEFORE installing setup.exe. You can sellect the language you want in this process.
3.After finishing Installation, DO NOT run your CLiP!!!
4.copy the RSRwin.ext to C:CLIP_X91LibApplication
5. Then run your CLiP, choose "Register me now" and in the next
Windows,please select "NO"!
6. Use this Key for Registration: 333DEF-111DEF-111DEF-222DEF-221DEF-000DEF
You can go to the GO2OBD.NET buy renault can clip.
autoscannertool by autoscannertool @
BMW ICOM ISTA A+B+C Firmware Only - Car Diagnostic Tool Supplier

With the growing maturity of automotive technology, speaking of the initiative to change. We should not unfamiliar, but the principle of their work is clear, here I am for you a rough introduction one or two Active steering is developed by BMW independent research and development due to the high cost, mainly loaded in the BMW intermediate car, such as the 5 Series 7 series X and GT The working principle of active steering is battery valve "variable differential motor controlled by ECU, to complete the transmission and planetary gear ratio, thereby changing the steering angle of output, generally speaking is when the vehicle in the steering wheel, from the left to the right end of a total of 2 times in the direction (to reduce the driver's actions. Rotate the tires, and thus a more efficient operation of mobile vehicle location easier) When the vehicle is running, the vehicle speed rises, the steering wheel from left to right, the total number of about 4 laps (the purpose is to adjust the angle of the tire more subtle angle, in order to complete a slight movement) .

and you can use the Ford-VCM OBD Diagnostic Interface High Quality

Ford-VCM OBD Diagnostic Interface is professional device for ford vehicles, Ford-VCM OBD has the most functions of ford vcm ids, it is the mini version of ford vcm ids. Ford-VCM OBD works on ford car by OBD2 port directly.It is designed for ford, mazda and other few brand cars, really working very well with those cars 1996-2010, some 2011 cars.

Ford-VCM OBD is diagnostic programmer for Ford vehicles 1996-2010. It can connect to various electronic control units (ECUs) and display identification, read and clear fault code memory, display and record measured values and perform actuator tests, some key programmer, etc.

Key features:

1.Support for wide range of ECUs and models
2.Easy connection via smart USB to OBD2 interface
3.Wide range of communication protocols and buses covered: 4.J1850 PWM, ISO, CAN
5.Automatic ECU recognition
6.Automatic vehicle scan
7.ECU Identification
8.Fault code (DTC) reading
9.Fault code clearing
10.Measured vaules / live data
11.Live data recording
12.Diagnostic protocol printing
13.Actuator tests
14.Control unit coding
15.PATS Immobilizer operations
16.Flash and serial memory programming

You can go to the GO2OBD.NET buy FORD VCM.
autoscannertool by autoscannertool @
1 pay attention to check the battery, the proposed change every four years.
If the battery has been used for more than four years, pay special attention to check if it can work properly and replace it, maybe it will strike in extreme weather. The capacity and discharge capacity of the car battery will decline after 2 years. General car battery life will not be more than 4 years. Of course, the maintenance of good battery life will be longer. In most parts of China, a good lead acid battery is not a freezing phenomenon. Car owners should pay more attention to the vehicle's battery, regularly check the battery status, to avoid excessive discharge battery. Such as the battery life has arrived, and found that the vehicle is difficult to start, headlight brightness, etc., to replace the battery as soon as possible.
2 regular replacement of oil filter, each time the replacement of oil filter oil filter.
Oil filter as a filter, oil filter is basically replace the oil, you need to replace the filter at the same time, of course, if it is normal to replace oil non periodic depends. Replace the full flow type oil filter, the paper filter. After a long time use of the paper filter, the filter efficiency will drop, the oil pressure through the filter will be greatly reduced. Although the pressure decreased to a certain extent, the filter bypass valve opens, the oil will enter through the bypass circuit to prevent the oil shortage, but this time to enter the oil oil unfiltered, causing pollutants into the oil, increase the wear of machine parts.
BMW ICOM A+B+C ISTA ISIS ISID is the latest version tool for programming, diagnosing, coding and complete system for BMW group which replace DIS GT1/SSS/OPS and OPPS. All BMW series (include Mini and Rolls-Ryce) can be processed with the ICOM-A, B and C-modules.
Please note: We do NOT sell BMW ICOM with mobile HDD, because software in mobile HDD is in VMWARE version whose running speed is very low and need complicated settings. We can give you vmware software FOR FREE if you need that.
If you want to buy more bmw icom you can ho to GO2OBD.NET.
123456 ... 9
New Post
feeds Feeds
autoscannertool Marier84 wildrownbaddflem chinggargsucne
Niki21 Andrea18 Rebecca28 Felicia20
Nikki20 Christina20 Allison28 Shanna21